Crawler, Wheeled or Square-Rod: Choosing from the SDLQ Drill Rig Line

SDLQ builds crawler rotary drilling rigs, wheeled rotary drilling rigs, tracked square-rod rigs, excavator-chassis modified rigs, CFA long auger rigs, hydraulic hammer pile drivers and photovoltaic (solar) pile drivers. The number of models looks large, but selection is not complicated: work down through bore diameter, maximum drilling depth, chassis type and Kelly bar type, and two or three rounds is usually enough.

First, fix the bore diameter. In the crawler range the maximum drilling diameter takes only two values: 1200 mm on the LQR120, and 1500 mm on the LQR-80, LQR100, LQR130, LQR130S and LQR150. This layer works as a threshold — up to 1500 mm the whole series qualifies, and the real differentiation starts at the next step.

Second, fix the maximum drilling depth. Within one series, depth is the main step-up: 15 m (LQR-80), 20 m (LQR100), 25 m (LQR120), 30 m (LQR130 and LQR130S) and 40 m (LQR150). 30 m is a useful dividing line — from the LQR130 upward the operating weight enters the 28 t class, so transport planning and ground bearing capacity have to be considered together.

Third, choose the chassis: crawler or wheeled. The crawler models run from 15.5 t (LQR-80) to 42 t (LQR150). Their low ground pressure suits soft ground, backfilled sites and large-diameter deep holes. Wheeled models are lighter and travel between sites under their own power, which suits municipal and smaller projects where the machine moves often.

The wheeled range is divided clearly as well. The LQ180-11, LQ180-13, LQ180-15, LQ180-18 and LQ180-20 share one platform: all 1500 mm bore diameter, with drilling depths of 10 m, 12 m, 14 m, 17 m and 19 m, and an operating weight of 8–9 t — the five models differ only in depth. The LQR-100W (1500 mm / 20 m / 17 t) and LQR360 (1500 mm / 20 m / 16 t) take the same bore diameter to a 20 m depth.

Fourth, look at the rod type. The tracked square-rod series — LQR154-11, LQR154-13, LQR154-15 and LQR154-18 — drills to 10 m, 12 m, 14 m and 17 m respectively, with rated output torque of 17/30 kN·m, positioned for fast, shallow holes. The interlocking Kelly bar crawler series covers 15–40 m for deeper piles. The two are not substitutes for each other; they divide the work by pile length.

Beyond the main line, four product families address specific conditions:

Excavator-chassis modified rigs: the LQR60S (1000 mm / 12 m / 9.5 t), the LQR-75S and LQR-75X (500–1200 mm / 15 m) and the LQR130X (400–1200 mm / 30 m). These suit customers who already own an excavator chassis and want to lower equipment investment.

CFA long auger rigs: the LQR180C offers a 1000 mm bore diameter and 25 m drilling depth; the LQR-260C offers 400–1200 mm, 30 m and a rated output torque of 260 kN·m — roughly double that of the main crawler line, for harder strata.

Hydraulic hammer pile drivers: the LQR-150H takes a 500 mm pile to 12 m at an operating weight of 38 t, for hammer-driven piling. Diesel hammer models are also available for different pile types.

Photovoltaic (solar) pile drivers: the LG3.5, LG4 and LG5 drill to 3.5 m, 4 m and 5 m. They are purpose-built for the short, numerous piles of solar mounting structures, and are correspondingly lighter.

The most commonly overlooked factor in selection is transport. Operating weight determines the transport plan: the 42 t of an LQR150 and the 8 t of an LQ180 series machine are two entirely different jobs. Transport dimensions need checking early as well — the LQR130, for example, measures 11800 mm long, 3000 mm wide and 3550 mm high in transport configuration, and low-bed trailer arrangements and oversize permits should be planned around those figures.

Putting the sequence together: filter by pile diameter first, then by pile length, then choose between crawler and wheeled according to site conditions and how often the machine will move, and finally judge whether a CFA, hammer or solar machine is required. By this point only one or two models usually remain, and the decision comes down to details such as winch configuration and engine power.

All figures above are taken from the official parameter tables for each model. Different configurations — rod length or track shoe width, for example — will produce different values, and the signed technical agreement governs. If you are selecting a machine for a specific pile diameter and length, send us the working conditions and we will suggest the matching model.

News